|
A VALUE FOR MORE THAN $$$$ OF EFFICIENT TECHNICAL INFORMATION FOR CONTRACTORS. ALL YOU NEED IS JUST PAY FOR ONLY .99 YOU GET ALL YOU NEED AT A DIGITAL DELIVERY FREE DIGITAL DELIVERY - ANYWHERE ON EARTH! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1,600+ Pages pages of written instruction, diagrams and illustrations INFOTECH manuals are compiled by InfoPros from official U.S. Department of Defense (declassified and non-classified) training manuals. These are the very same materials used to train our military men and women. Manuals are in Adobe PDF. View on screen, Print, Rotate, and Zoom to 1600x for great detail. Fully categorized and easy to navigate, allowing you to find the manuals you desire within minutes. **************************************** * PLUMBING I : PREPARE A PLUMBING TAKEOFF LIST [82 pages] * PLUMBING II: WATER SUPPLY [78 pages] * PLUMBING III: WASTE SYSTEMS [101 pages] * PLUMBING IV: PLUMBING FIXTURES [96 pages] * PLUMBING V: REPAIR VALVES AND FIXTURE CONTROL DEVICES [57 pages] * PLUMBING VI: CLEAR WASTE SYSTEM STOPPAGES [32 pages] * PLUMBING, PIPE FITTING, AND SEWERAGE (275 pages) * BASIC HYDRAULICS AND HYDRAULIC PLUMBING [76 pages] * CONSTRUCTION PRINT READING (500 pages) **************************************** (1) PLUMBING: PREPARE A PLUMBING TAKEOFF LIST [82 pages] This course is designed teach the knowledge necessary to extract information from a construction drawing legend, identify plumbing symbols, and use plumbing material. Lesson <1>: USE DRAWING LEGENDS AND PLUMBING SYMBOLS * Read a Construction Drawing * Identify Water System Pipelines * Identify Waste System Pipelines Lesson <2>: LIST PLUMBING MATERIALS * List Water and Waste Line Fittings (2) PLUMBING: WATER SUPPLY [78 pages] The water supply course is designed to teach the knowledge necessary for performing tasks related to preparing pipes and connecting and installing water pipelines. The course is presented in two lessons. Lesson <1>: Water Supply Systems and Materials * Identifying Types of Piping Materials * Preparing Piping Materials Lesson <2>: Rough-In Water Supplies and Lines * Using Fittings on Pipe Runs * Installing Water Line Pipe Runs (3) PLUMBING: WASTE SYSTEMS [101 pages] The waste system course is designated to teach those tasks necessary to prepare, connect, and install pipes in a waste system. The course is presented in two lessons covering Waste System Materials and Waste System Roughing-in. Lesson <1>: Waste Systems And Materials * Classifying Types of Piping * Preparing Piping Materials * Identifying Fittings and Using Joint Connections for Rigid Plastic Pipe * Identifying Fittings and Using Joint Connections for Galvanized Steel Pipe * Identifying Fittings and Using Joint Connections for Rigid Copper Tubing Lesson <2>: Waste System Roughing-In * Installing Sewer Pipelines * Installing Drain Lines and Stacks * Installing Piping Material * Testing the System for Leaks (4) PLUMBING: PLUMBING FIXTURES [96 pages] The plumbing fixtures course, part of the Plumber MOS 51K Skill Levels 1 and 2 course, is designed to teach the skills and knowledge necessary for performing tasks related to installing plumbing fixtures such as lavatories and sinks, water closets with tanks, and urinals. Lesson <1>: INSTALLATION OF LAVATORIES AND SINKS * Identifying Lavatories and Sinks * Installing Wall-Hung Lavatories * Installing Shutoff Angle Valves * Installing Flexible Tubing * Testing for Mechanical Operation and Leaks Lesson <2>: INSTALLATION OF WATER CLOSETS WITH FLUSHING DEVICES * Attaching Flushing Devices * Installing Flushing Mechanisms * Adjusting Flushing Mechanisms Lesson <3>: INSTALLATION OF URINALS * Installing Wall-Hung Urinals * Connecting P-Traps to Urinals (5) PLUMBING: REPAIR VALVES AND FIXTURE CONTROL DEVICES [57 pages] This course presents a survey of the functions of management, the principles governing the functions and their ability to apply them to construction management. An understanding of these factors and the ability to apply them to construction projects is essential to the engineer company commander and the members of the battalion staff. * Lesson <1>: Maintenance of Valves * Lesson <2>: Maintenance of Fixture Control Devices (6) PLUMBING VI: CLEAR WASTE SYSTEM STOPPAGES [32 pages] The Clear Waste System Stoppages course is designed to teach the knowledge necessary for performing tasks related to clearing stoppages in plumbing fixtures and waste drain lines. The course is presented in two lessons, each corresponding to a terminal objective as indicated below: Lesson <1>: Clear Stoppages In Plumbing Fixtures * Identifying Clearing Tools * Clearing Stoppages In Fixtures Lesson <2>: Clear Stoppages in Waste Lines * Locating and Clearing Stoppages in Waste Lines (7) PLUMBING, PIPE FITTING, AND SEWERAGE (275 pages) This manual is a guide for engineer personnel responsible for conducting plumbing and pipe fitting operations. This manual provides information on water, waste, and heating systems and basic plumbing techniques. Use this guide to help repair fixtures, leaky pipes, and valves; to make pipe joints; install water, waste, and heating systems; and test and service these systems. Section I - Basic Water Supply and Water Distribution Systems * Water Supply Lines and Branches * Installing Curb and Meter Stops * Fire-Protection Water Systems Section II - Theater of Operations Water Supply and Distribution System * Water Distribution Methods * Sewage Disposal Facilities * Field Expedient Facilities * Fixed and Installation Facilities Section VII - Human Waste Disposal in the Field * Constructing and Closing Latrines * Latrines in Areas With High Groundwater Tables * Maintenance of Urine Disposal Facilities Section VIII - Wastewater Disposal in the Field * Forced-Air Heating Systems Chapter <3> Basic Plumbing Repairs and Maintenance * Water Supply and Piping Requirement Chapter <6> Pipes and Fittings * Cast-Iron Soil Pipe and Fittings * Galvanized-Steel/Iron Pipe and Fittings * Copper Tubing and Fittings * Other Types of Pipes and Fittings Chapter <7> Valves and Faucets Chapter <8> Stacks and Branches Chapter <10> Steam, Gas, and Air Piping Chapter <11> Centrifugal Pumps * Installation and Operation Appendix A Metric Conversion Chart Appendix B Construction Plans and Drawings Section I - Plans and Drawings (8) BASIC HYDRAULICS AND HYDRAULIC PLUMBING [76 pages] We designed this course to provide instruction on the science of hydraulics, an explanation of hydraulic principles, and a study of the fluids used in aircraft hydraulic systems. You will also be introduced to the fundamentals of hydraulic plumbing, techniques of fabricating tubes and hoses, principles of installing these lines, and use of seals and gaskets to control leakage in plumbing systems. * Lesson 1: Basic Hydraulics * Lesson 2: Hydraulic Plumbing * Appendix A: Proof Testing of Hose Assemblies As an engineer officer you may be assigned the job of directing some phase of utilities work. To do this efficiently, you must understand the broad, general phases of utilities operations. That is the purpose of this subcourse. It is planned to give you basic knowledge in utilities layout, installation, and operation. Lesson 1: Organization and Functions of Utilities Engineer Service Teams Lesson 2: Electric Power Systems Lesson 3: Refrigeration Systems Lesson 4: Water Supply and Distribution Systems Lesson 5: Plumbing Installations and Bills of Materials Lesson 6: Sewerage Systems Lesson 7: Rehabilitation of Utilities The material in this course broadly covers the principles involved, and the methods and equipment employed, in the design, construction, and operation of electric power and distribution systems, water supply distribution systems, and sewage collection and treatment systems. Large semipermanent installations in a theater of operations such as depots, base hospitals, replacement depots, and the like require fairly extensive, complex utilities systems. The design, construction, rehabilitation (where necessary) and operation of these systems are responsibilities of engineer units. While this course will not make you an expert, it will furnish sufficient basic information to enable you to function as an engineer staff officer or commander in the communications zone of a theater of operations. Lesson 1: Electric Power Systems Lesson 2: Electrical Distribution Systems Lesson 3: Water Distribution Systems Lesson 4: Sewage Collection and Disposal (11) CONSTRUCTION PRINT READING (500 pages) Construction print reading is a key skill for technical students. Fortunately, a formal education is not essential for achieving proficiency in this important subject; the study of correspondence courses such as this can provide the essential skills. Lesson 1: Principles and Methods Lesson 2: Architectural Drawings Lesson 3: Utilities Drawings Lesson 4: Heating, Air-Conditioning, and Refrigeration Drawings Lesson 5: Bills of Materials Appendix B: Conversion Tables Please feel free to ask any question. The tech support will be 24 hours a day. Thank you. (please look at our rules and privacy policy) |
hermanpatterson@modularparts.com (Herman Patterson) for more information. This email will be sent to Herman Patterson' actual email address.
